RedSealCarpenterExam

🧰 Common Occupational Skills

What this topic covers

Major Work Activity A of the RSOS Carpenter 2022, Performs common occupational skills, accounts for 12 questions out of 100: task A-1 Uses and maintains tools and equipment (4), A-2 Performs safety-related activities (3), A-3 Builds and uses temporary access structures (3) and A-4 Uses communication and mentoring techniques (2). Sub-tasks A-1.06 and A-1.07 are not common core and are not tested. These are original study notes, not documents of the Red Seal Program, the CCDA, ESDC or any province. Code values refer to the National Building Code of Canada 2020, the edition supplied at the exam; a value that changes in the NBC 2025 is given with both editions. Health and safety rules and CSA standards vary by province and manufacturer: work according to jurisdictional regulations and manufacturers' specifications.

Tools and equipment

Rigging and layout instruments

PPE and safe work environment

Temporary access structures

Communication and mentoring

Take the free test · full question bank and mock exams with a subscription

Sample questions (10)

1. In what kind of area should hand and power tools be stored between uses?

  1. A clean, dry, ventilated and secure area
  2. A sheltered open bay beside the loading zone
  3. A sealed, unheated container with no air flow
  4. A cool lower level where moisture collects

Criterion A-1.01.01P of RSOS sub-task A-1.01 has tools organized and stored in a clean, dry, ventilated and secure area to prevent damage. A bay beside the loading zone is open to traffic and theft, a sealed container with no air flow traps condensation that rusts steel, and a lower level where moisture collects invites corrosion.

2. When should the receiver tank of a portable air compressor be drained of condensed water?

  1. Once a year, at the annual inspection by a technician
  2. After use, per the manufacturer's specifications
  3. Whenever the safety valve has released pressure
  4. After the air hose has been repaired or replaced

Criterion A-1.01.10P of RSOS sub-task A-1.01 has the tank drained after use according to the manufacturer's specifications, which prevents corrosion of the tank and damage to tools. An annual inspection leaves water in the tank for months, a hose repair has no bearing on condensation, and a safety-valve release signals a fault rather than a draining schedule.

3. A pneumatic nailer cycles slowly and shows rust at its air inlet after a wet week. What is the most likely cause?

  1. A regulator set a little above the working pressure
  2. A magazine loaded with nails longer than the tool specifies
  3. Moisture from an undrained tank and missed lubrication
  4. A depth-of-drive wheel left at its shallowest setting

RSOS sub-task A-1.01 includes draining the compressor tank after use, lubricating pneumatic tools and changing their oil and filter as the manufacturer specifies, because water carried in the air rusts internal parts and slows the tool. Over-long nails, slightly high pressure or a shallow depth setting change how the nails seat but do not corrode an air inlet or slow the cycle.

4. What is the purpose of the riving knife fitted behind the blade of a table saw?

  1. To hold the workpiece tight against the fence
  2. To keep the kerf open and help prevent kickback
  3. To carry sawdust away from the cutting area
  4. To lock the blade at the chosen bevel angle

A riving knife sits just behind the blade and keeps the cut from closing on it, which helps prevent kickback; RSOS sub-task A-1.02 lists anti-kickback devices among the guards to maintain. Pressing the stock to the fence is the job of a featherboard, dust is removed through a collection port, and the bevel angle is locked at the tilt mechanism.

5. A table saw blade is dull and burning the edges of the boards it rips. What is the correct action?

  1. Feed the boards through the blade harder to reduce burning.
  2. Sharpen or replace it as the manufacturer specifies.
  3. Remove the blade guard to see the cut line better.
  4. Let the saw idle for a minute so the blade cools down.

Criterion A-1.02.01P of RSOS sub-task A-1.02 has dull or damaged cutting attachments removed, replaced or sharpened according to the manufacturers' specifications. Forcing the feed overloads the motor and raises the risk of kickback, removing the guard exposes the operator to the blade, and idling the saw cools the blade but does not restore its edge.

6. What must a worker have before operating a powder-actuated tool on a job site?

  1. Several years of experience with pneumatic framing nailers
  2. A verbal approval from the supervisor each morning
  3. The training and certification the jurisdiction requires
  4. A quick read of the owner's manual before first use

RSOS sub-task A-1.03 (outcome A-1.03.04L) covers the training and certification requirements for powder-actuated tools, and criterion A-1.03.06P has them used according to jurisdictional requirements. Daily approval, experience with another type of tool and a quick read of the manual are not substitutes for the required certification.

7. A powder-actuated tool misfires when the trigger is pulled. What is the correct next step?

  1. Hold it on the work for the specified wait, then follow the maker's steps.
  2. Open the tool right away and put the shot into a pocket of the work apron.
  3. Set the loaded tool down on the deck and carry on to the next fastening point.
  4. Pull the trigger again straight away, keeping the tool pressed against the work.

Criterion A-1.03.06P of RSOS sub-task A-1.03 has powder-actuated tools used according to the manufacturer's specifications and criterion A-1.03.05P has misfired shots handled and disposed of the same way, so the operator holds the tool against the work for the wait the manufacturer specifies before following its misfire steps. Re-firing at once or opening the tool without waiting risks a delayed discharge, a live shot carried in an apron pocket is unsecured, and a loaded tool left on the deck can be picked up and fired by anyone.

8. A 12 kN (2 700 lb.) load hangs from a two-leg sling whose legs each make 60 degrees with the horizontal. Tension in each leg = half the load divided by the sine of the leg angle (sin 60 degrees = 0.866). What is the tension in each leg, to the nearest 0.1 kN and to the nearest pound?

  1. Metric: 6.9 kN, Imperial: 1 559 lb.
  2. Metric: 12.0 kN, Imperial: 2 700 lb.
  3. Metric: 13.9 kN, Imperial: 3 118 lb.
  4. Metric: 6.0 kN, Imperial: 1 350 lb.

Metric: (12 kN / 2) / 0.866 = 6.93, or 6.9 kN per leg; Imperial: (2 700 lb. / 2) / 0.866 = 1 558.9, or 1 559 lb. per leg, a sling-angle calculation listed in RSOS sub-task A-1.04. Leaving out the sine gives 6.0 kN and 1 350 lb., and taking the angle from the vertical (cos 60 degrees = 0.5) gives 12.0 kN and 2 700 lb. Forgetting to halve the load gives 13.9 kN and 3 118 lb.

9. What is the purpose of a tag line attached to a load being hoisted?

  1. To share the load weight with the main sling
  2. To signal the operator when the load is ready to lift
  3. To guide and control the load while it is moving
  4. To extend the reach of the hook past its lifting limit

Criterion A-1.04.07P of RSOS sub-task A-1.04 has tag lines used to guide and control the load, so a worker can steer it from a safe distance. A tag line carries no meaningful share of the weight, signals to the operator are given by hand signals (criterion A-1.04.01P) rather than by tugging a line, and a tag line cannot extend the reach of the hook.

10. Why is dunnage placed under a load that will be lifted with slings?

  1. It raises the load so the crane operator can see it better
  2. It leaves room to pass the slings or chains under the load
  3. It increases the working load limit of the sling in use
  4. It lets the load be dragged to the lifting point more easily

Criterion A-1.04.04P of RSOS sub-task A-1.04 has the load prepared using dunnage to give access for lifting chains and slings, and for storage. Dunnage does not make the load more visible to the operator, is not meant for dragging, and has no effect on the working load limit of the sling, which is set by the sling and its configuration.

Start free

RedSealCarpenterExam · Topics · Exam guide · Sample questions